ADM5170 Octal, RS-232/RS-423 Line Driver

Product DetailsThe ADM5170 is an octal line driver suitable for digital communication systems with data rates up to 116 kB/s. Input TTL or CMOS signal levels are inverted and translated into either EIA RS-232E or RS-423A signal levels depending on the sta

ADM222 High Speed, 5 V, 0.1 µF CMOS RS-232 Transceiver with 2 Drivers, 2 Receivers, 200kBPS Data Rate and a Shutdown Pin

Product DetailsThe ADM222,ADM232A,ADM242are a family of high-speed RS-232 line drivers/receivers offering transmission rates up to 200 kB/s. Operating from a single 5 V power supply, a highly efficient on-chip charge pump using small (0.1 µF) extern

LT1039A Triple RS232 Driver/Receiver with Shutdown

Product DetailsThe LT1039A is a triple RS232 driver/receiver that includes shutdown. Each receiver will accept up to ±30V input and can drive either TTL or CMOS logic. The RS232 drivers accept TTL logic inputs and output RS232 voltage levels. The o

LTC1687 52Mbps Precision Delay RS485 Fail-Safe Transceivers

Product DetailsThe LTC1686/LTC1687 are high speed, precision delay, full-duplex RS485 transceivers that can operate at data rates as high as 52Mbps. The devices also meet the requirements of RS422.A unique architecture provides very stable propagation del

LTC1535 Isolated RS485 Transceiver

Product DetailsThe LTC1535 is an isolated RS485 full-duplex differential line transceiver. Isolated RS485 is ideal for systems where the ground loop is broken to allow for much larger common mode voltage ranges. An internal capacitive isolation barrier pr

ADM3307E +2.7V Serial Port RS-232 Transceiver (5 Drivers / 3 Receivers) with 15kV ESD (TTL & RS-232)

Product DetailsOperating from a single supply as low as +2.7 V, the ADM3307E is a five-driver/three-receiver serial port transceiver, and fully meets full EIA-232 standards. It features an on-board, charge pump dc-to-dc converter, which eliminates the nee

ADM2582E 2.5 kV Signal and Power Isolated, ±15 kV ESD Protected, Full/Half Duplex RS-485 Transceiver (16Mbps)

Product DetailsThe ADM2582E/ADM2587Eare fully integrated signal and power isolated data transceivers with ±15 kV ESD protection and are suitable for high speed communication on multipoint transmission lines. The ADM2582E/ADM2587E include an integra

ADM2481 2.5 kV Signal Isolated, 500 kbps, Half Duplex RS-485 Transceiver

Product DetailsThe ADM2481 differential bus transceiver is an integrated, galvanically isolated component designed for bidirectional data communication on balanced, multipoint bus transmission lines. It complies with ANSI EIA/TIA-485-A and ISO 8482: 1987(

LTC1334 Single 5V RS232/RS485 Multiprotocol Transceiver

Product DetailsThe LTC1334 is a low power CMOS bidirectional transceiver featuring two reconfigurable interface ports. It can be configured as two RS485 differential ports, as two dual RS232 single-ended ports or as one RS485 differential port and one dua

LTC1387 Single 5V RS232/RS485 Multiprotocol Transceiver

Product DetailsThe LTC1387 is a low power reconfigurable CMOS bidirectional transceiver. It can be configured as an RS485 differential port or as two RS232 single-ended ports. An onboard charge pump uses four 0.1µF capacitors to generate boosted pos

ADN4666 3 V, LVDS, Quad CMOS Differential Line Receiver

Product DetailsThe ADN4666 is a quad-channel, CMOS low voltage differential signaling (LVDS) line receiver offering data rates of over 400 Mbps (200 MHz) and ultralow power consumption.The device accepts low voltage (350 mV typical) differential input sig

ADN4694E 3.3 V, 100 Mbps, Half-Duplex, High Speed M-LVDS Transceiver with Type 2 Receiver

Product DetailsTheADN4690E/ADN4692E/ ADN4694E /ADN4695Eare multipoint, low voltage differential signaling (M-LVDS) transceivers (driver and receiver pairs) that can operate at up to 100 Mbps (50 MHz). Slew rate control is implemented on the driver outputs

ADG3301 Low Voltage 1.15 V to 5.5 V, Single-Channel Bidirectional Logic Level Translator

Product DetailsTheADG3301 is a single channel bidirectional logic level translator. It can be used in multivoltage digital system applications such as data transfer between a low voltage DSP/controller and a higher voltage device. The internal architectur

ADG3308-1 Low Voltage, 1.15 V to 5.5 V, 8-Channel Bidirectional Logic Level Translators

Product DetailsThe ADG3308-1 is a bidirectional level translator containing eight bidirectional channels. They can be used in multivoltage digital system applications such as a data transfer between a low voltage DSP controller and a higher voltage device

ADUM1440 Micropower Quad-Channel Digital Isolator, Default High (4/0 Channel Directionality)

Product DetailsThe ADuM1440 is a micropower, quad-channel digital isolator which has a default high and 4/0 channel directionality based on the Analog Devices, Inc.,iCoupler®technology. (Dual-channel products available.) Combining high speed, compleme

ADE7912 2-Channel, Isolated, Sigma Delta ADC with SPI

Product DetailsThe ADE7912/ADE7913are isolated, 3-channel Σ-Δ ADCs for a variety of applications such as shunt-based polyphase meters, power quality monitoring, solar inverters, process monitoring and protective devices. Data and power isolati

ADuM231D Robust 5kV RMS Triple Channel Digital Isolators, Input Disable (2/1 Channel Directionality)

Product DetailsTheADuM230D/ADuM230E/ADuM231D/ADuM231Eare triple-channel digital isolators based on Analog Devices, Inc.,iCoupler®technology. Combining high speed, complementary metal-oxide semiconductor (CMOS) and monolithic air core transformer techn

ADuM230D Robust 5kV RMS Triple Channel Digital Isolators, Input Disable (3/0 Channel Directionality)

Product DetailsThe ADuM230D/ADuM230E/ADuM231D/ADuM231Eare triple-channel digital isolators based on Analog Devices, Inc.,iCoupler®technology. Combining high speed, complementary metal-oxide semiconductor (CMOS) and monolithic air core transformer tech

ADuM250N Robust 5.0 kVrms Five Channel Digital Isolator w/ Fail-Safe & 0 Reverse Channels

Product DetailsThe ADuM250N/ADuM251N/ADuM252Nare 5-channel digital isolators based on Analog Devices, Inc.,iCoupler®technology. Combining high speed, complementary metal-oxide semiconductor (CMOS) and monolithic air core transformer technology, these

LTM9100 Anyside™ High Voltage Isolated Switch Controller with I2C Command and Telemetry

Product DetailsThe LTM9100 μModule®(micromodule) controller is a complete, galvanically isolated switch controller with I2C interface, for use as a load switch or hot swap controller. The load is soft started and controlled by an external N-channel

Pagina 1 / 25